Category Archives: MANAGEMENT

GUEST LECTURE on “Advanced techniques for Smart Phone service and Troubleshooting”

Topic: Advanced techniques for Smart Phone service and Troubleshooting    

Date:   4.10.2019 & 5.10.2019(Two days)

Venue: B-Block (RF Lab & Microprocessor Lab)      Target Audience: II, III and IV year ECE

Resource person: Mr.R.Karthi, New Technology,Mobile Service & Training Institute, Coimbatore.

Objective of Program: To make the student to understand about tracking, identifying Components, Trouble Shooting and also assembles and dissemble the Mobile Phone.

Topics Covered:

  1. Basics of Electronic Components
  2. Current and voltage power
  3. AC current and DC Current
  4. IC Identification in mobile phone.
  5. Testing of Battery and Components by using various Testing method.
  6. Circuit Diagram for i) Speaker and Ringer Solution ii) Insert SIM (or) No Signal Solution (iii) Charging Solution
  7. Checking of Speaker, Mike and Ringer in Mobile phone.
  8. Dead Mobile Solution
  9. Software Problems in Mobile phone.

Outcomes:

CO1: Identification of Active and Passive Component in the PCB Board inside the mobile phone

CO2: Students have learned about how to diagnose the mobile Phone.

CO3: Students have learned about how to replace the components according to the problem occur in the mobile phone.

CO4: The Students have gained basic knowledge to become the Entrepreneur in mobile session.

PO & PSO Mapping:

PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 PO10 PO11 PO12 PSO1 PSO2
M H H H L M M H M M

GUEST LECTURE : “Indoor Air Quality Management”

Topic: “Indoor Air Quality Management”                                            Date: 03.10.2019

Venue: B-Block seminar Hall                                                Target Audience: III Year EEE

Resource person: Dr.G. Venkatesan, Assistant Professor,Department of civil Engineering, Anna University Bit campus,Trichy

Objective of Program: To impart knowledge on Indoor air pollutant and its management.

Topics Covered:

  • Indoor air quality management.
  • The theories for major air pollutant control.

Outcomes:

  • Ability to understand characteristics of indoor air pollutants.
  • Ability to design and particulate air pollution control devices.
  • Ability to manage Indoor air quality. 

PO & PSO Mapping:

PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 PO10 PO11 PO12 PSO1 PSO2
H M H M M

WORKSHOP : “PCB DESIGNING AND MAKING CIRCUITS”

Topic: “PCB DESIGNING AND MAKING CIRCUITS”            Date: 03.10.2019 & 04.10.2019   

Venue: B-Block-Research and development lab              Target Audience: IETE(EEE) Students

Resource person: Mr.E.Arunvijayan & Team, Pantech Proed Private Limited -Trichy

Objective of Program:

  • To gain basic concept of PCB design.
  • To provide design knowledge with Proteus software.
  • Expose the students to practical process of PC board preparation.

Topics Covered:

  • Introduction to Proteus software.
  • Basic Schematic Circuit Drawing using software.
  • Design of Oscillator and Multivibrator circuits in PCB.

Outcomes:

  • Students can able to understand PCB vital role in engineering field.
  • Students can able to do the design the circuits with Proteus software.
  • Students can able to prepare the designed PCB with raw material.

PO & PSO Mapping:

PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 PO10 PO11 PO12 PSO1 PSO2
M H H M H M M H H